- mice-discuss - lists.micemn.net

Voting Reminder

by Jason Hanke

You cannot vote remotely in the election at today's meeting without a proxy. Please assign a proxy or email me your vote and I will act as your proxy. We currently have proxies registered for the following ASNs: AS53597 AS20940 AS57 AS32609 AS47096 AS15011 AS13573 -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 27, 2016

Re: Agenda and Request - UG 21

by Chris Wopat

Conference bridge info? Thanks, -- Chris Wopat Network Engineer, WiscNet wopat(a)wiscnet.net 608-210-3965

Sept. 27, 2016

Re: Agenda and Request - UG 21

by Shaun Carlson

I'll correct, thanks! Shaun Carlson Director of Information Technology | Arvig ph: (218) 346.8673 | em: shaun.carlson(a)arvig.com On Tue, Sep 27, 2016 at 7:11 AM -0500, "Jeremy Lumby" <jlumby(a)mnvoip.com> wrote: I noticed the agenda states the meeting starts at 4, however everything else has said 3. Just wanted to verify it is 3. From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Shaun Carlson Sent: Monday, September 26, 2016 9:42 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: [MICE-DISCUSS] Agenda and Request - UG 21 All, Attached is the UG 21 Agenda for tomorrow's meeting. I've also attached the UG 20 minutes for your review prior to the meeting tomorrow. I also have a request. I'm looking for a volunteer to take minutes on behalf of the board for this meeting as I will be unable to attend. We had an unexpected death this weekend of a long-term Arvig employee and it's having a great impact on my team. I need to be at our locations this week to be part of the support and recovery process. I appreciate your understanding in this matter and would not, normally, miss a meeting as important as this. As an FYI, I've communicated this to the board and am working on sharing all relevant files (to include the non-profit information) to the board for access. Please let me know if you're willing to take and distribute minutes and I'll get you the relevant files and instructions. I truly appreciate what this organization does, what it means for the state and I'm honored to have been able to serve you in this capacity for the last few years. I, and Arvig, still plan to be an active part of MICE and support it in whatever capacity best fits the needs of the organization and it's members. Thank you! s Shaun Carlson Director of Information Technology | Arvig ph: (218) 346-8673 | em: shaun.carlson(a)arvig.com To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1

Sept. 27, 2016

Re: Agenda and Request - UG 21

by Jeremy Lumby

I noticed the agenda states the meeting starts at 4, however everything else has said 3. Just wanted to verify it is 3. From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Shaun Carlson Sent: Monday, September 26, 2016 9:42 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: [MICE-DISCUSS] Agenda and Request - UG 21 All, Attached is the UG 21 Agenda for tomorrow's meeting. I've also attached the UG 20 minutes for your review prior to the meeting tomorrow. I also have a request. I'm looking for a volunteer to take minutes on behalf of the board for this meeting as I will be unable to attend. We had an unexpected death this weekend of a long-term Arvig employee and it's having a great impact on my team. I need to be at our locations this week to be part of the support and recovery process. I appreciate your understanding in this matter and would not, normally, miss a meeting as important as this. As an FYI, I've communicated this to the board and am working on sharing all relevant files (to include the non-profit information) to the board for access. Please let me know if you're willing to take and distribute minutes and I'll get you the relevant files and instructions. I truly appreciate what this organization does, what it means for the state and I'm honored to have been able to serve you in this capacity for the last few years. I, and Arvig, still plan to be an active part of MICE and support it in whatever capacity best fits the needs of the organization and it's members. Thank you! s Shaun Carlson Director of Information Technology | Arvig ph: (218) 346-8673 | em: shaun.carlson(a)arvig.com To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1

Sept. 27, 2016

Agenda and Request - UG 21

by Shaun Carlson

All, Attached is the UG 21 Agenda for tomorrow's meeting. I've also attached the UG 20 minutes for your review prior to the meeting tomorrow. I also have a request. I'm looking for a volunteer to take minutes on behalf of the board for this meeting as I will be unable to attend. We had an unexpected death this weekend of a long-term Arvig employee and it's having a great impact on my team. I need to be at our locations this week to be part of the support and recovery process. I appreciate your understanding in this matter and would not, normally, miss a meeting as important as this. As an FYI, I've communicated this to the board and am working on sharing all relevant files (to include the non-profit information) to the board for access. Please let me know if you're willing to take and distribute minutes and I'll get you the relevant files and instructions. I truly appreciate what this organization does, what it means for the state and I'm honored to have been able to serve you in this capacity for the last few years. I, and Arvig, still plan to be an active part of MICE and support it in whatever capacity best fits the needs of the organization and it's members. Thank you! s *Shaun Carlson*Director of Information Technology | Arvig ph: (218) 346-8673 | em: shaun.carlson(a)arvig.com

Sept. 27, 2016

Re: Congrats at 100G

by Jeremy Lumby

We probably would have still made it without Yahoo. I think their growth has been slowed a little bit since they are bilateral only and I don't think that everyone has gotten around to setting up their bgp sessions. I wonder if it is worth posting invitations like theirs to the announce list since many of the network admins at the eyeball networks don't follow the discuss list so that they can keep the chatter in their inboxes lower. Jeremy Lumby Minnesota VoIP 9217 17th Ave S Suite 216 Bloomington MN 55425 Direct 612.392.6814 Main 612.355.7740 EFax 952.873.7425 -------- Original message -------- From: Frank Bulk <fbulk(a)MYPREMIERONLINE.COM> Date: 9/26/16 8:04 PM (GMT-06:00) To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] Congrats at 100G _____ >From : Frank Bulk [fbulk(a)MYPREMIERONLINE.COM] To : MICE-DISCUSS(a)LISTS.IPHOUSE.NET [MICE-DISCUSS(a)LISTS.IPHOUSE.NET] Date : Monday, September 26 2016 20:04:56 Was it Yahoo traffic that brought it over the top, or just organic growth? Frank -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby Sent: Sunday, September 25, 2016 9:10 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: [MICE-DISCUSS] Congrats at 100G I just wanted to say congrats to everyone. I believe for the first time MICE broke the 100G mark I show the high traffic level as 104G just about 1/2 hour ago. I am very excited knowing that there are many others in the process of upgrading their connection, and newly connecting that should make this number continue to grow quickly in the very near future. Jeremy Lumby Minnesota VoIP 9217 17th Ave S Suite 216 Bloomington, MN 55425 Main: 612-355-7740 x211 Direct: 612-392-6814 EFax: 952-873-7425 jlumby(a)mnvoip.com

Sept. 27, 2016

Re: Congrats at 100G

by Frank Bulk

Was it Yahoo traffic that brought it over the top, or just organic growth? Frank -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby Sent: Sunday, September 25, 2016 9:10 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: [MICE-DISCUSS] Congrats at 100G I just wanted to say congrats to everyone. I believe for the first time MICE broke the 100G mark I show the high traffic level as 104G just about 1/2 hour ago. I am very excited knowing that there are many others in the process of upgrading their connection, and newly connecting that should make this number continue to grow quickly in the very near future. Jeremy Lumby Minnesota VoIP 9217 17th Ave S Suite 216 Bloomington, MN 55425 Main: 612-355-7740 x211 Direct: 612-392-6814 EFax: 952-873-7425 jlumby(a)mnvoip.com

Sept. 27, 2016

Proxy Votes

by Jason Hanke

If you will not be at the meeting or will be attending remotely please assign a proxy to cast your vote in the election. There is one vote available per member. Results will be announced following the meeting. Voting instruments will be distributed at the meeting. Voters (or proxies) must be present to vote. Please email peering(a)micemn.net to assign your proxy. You can alternatively email peering(a)micemn.net who you would like to vote for and I will act as your proxy. -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 26, 2016

Re: Congrats at 100G

by Jason Hanke

This is a pretty big deal! Please help us spread the word! Sharing, commenting and tagging is best (Likes don't always put it in your timeline): Facebook: https://www.facebook.com/MNMICE/photos/a.1811339929145572.1073741827.173015… LinkedIn: https://www.linkedin.com/groups/3000346/3000346-6186193398748237827 Thanks! Jay On Mon, Sep 26, 2016 at 5:52 AM, Hannigan, Martin <marty(a)akamai.com> wrote: > > > I won’t be surprised if it happens again tonight. The debate is being tagged as potentially bigger than the Super Bowl, off and online. > > Great stuff team! > > > >> On Sep 25, 2016, at 10:10 PM, Jeremy Lumby <jlumby(a)MNVOIP.COM> wrote: >> >> I just wanted to say congrats to everyone. I believe for the first time MICE broke the 100G mark I show the high traffic level as 104G just about 1/2 hour ago. I am very excited knowing that there are many others in the process of upgrading their connection, and newly connecting that should make this number continue to grow quickly in the very near future. >> >> >> Jeremy Lumby >> Minnesota VoIP >> 9217 17th Ave S >> Suite 216 >> Bloomington, MN 55425 >> Main: 612-355-7740 x211 >> Direct: 612-392-6814 >> EFax: 952-873-7425 >> jlumby(a)mnvoip.com > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 26, 2016

Re: Congrats at 100G

by Hannigan, Martin

I won’t be surprised if it happens again tonight. The debate is being tagged as potentially bigger than the Super Bowl, off and online. Great stuff team! > On Sep 25, 2016, at 10:10 PM, Jeremy Lumby <jlumby(a)MNVOIP.COM> wrote: > > I just wanted to say congrats to everyone. I believe for the first time MICE broke the 100G mark I show the high traffic level as 104G just about 1/2 hour ago. I am very excited knowing that there are many others in the process of upgrading their connection, and newly connecting that should make this number continue to grow quickly in the very near future. > > > Jeremy Lumby > Minnesota VoIP > 9217 17th Ave S > Suite 216 > Bloomington, MN 55425 > Main: 612-355-7740 x211 > Direct: 612-392-6814 > EFax: 952-873-7425 > jlumby(a)mnvoip.com

Sept. 26, 2016

Re: Congrats at 100G

by Reid Fishler

Well-done folks! Reid On Sep 25, 2016 10:10 PM, "Jeremy Lumby" <jlumby(a)mnvoip.com> wrote: > I just wanted to say congrats to everyone. I believe for the first time > MICE broke the 100G mark I show the high traffic level as 104G just about > 1/2 hour ago. I am very excited knowing that there are many others in the > process of upgrading their connection, and newly connecting that should > make this number continue to grow quickly in the very near future. > > > Jeremy Lumby > Minnesota VoIP > 9217 17th Ave S > Suite 216 > Bloomington, MN 55425 > Main: 612-355-7740 x211 > Direct: 612-392-6814 > EFax: 952-873-7425 > jlumby(a)mnvoip.com > >

Sept. 26, 2016

Congrats at 100G

by Jeremy Lumby

I just wanted to say congrats to everyone. I believe for the first time MICE broke the 100G mark I show the high traffic level as 104G just about 1/2 hour ago. I am very excited knowing that there are many others in the process of upgrading their connection, and newly connecting that should make this number continue to grow quickly in the very near future. Jeremy Lumby Minnesota VoIP 9217 17th Ave S Suite 216 Bloomington, MN 55425 Main: 612-355-7740 x211 Direct: 612-392-6814 EFax: 952-873-7425 jlumby(a)mnvoip.com

Sept. 26, 2016

Proxies

by DeLong, Owen

Those who will not be at the meeting next week and wish to vote for me may do so by requesting that Mr. Jayson Hanke (CC’d above) carry a proxy on your behalf. Thank you in advance for your support, Owen

Sept. 26, 2016

Re: IPv6 usage

by Doug McIntyre

On Sat, Sep 24, 2016 at 04:37:21PM +0000, Frank Bulk wrote: > It appears the JunOS is able to break out the amount of IPv6 (https://www.juniper.net/documentation/en_US/junos16.1/topics/reference/comm…) on an interface. Doesn't look like it actually counts on this platform.. dmcintyre@MICE-SW1> show interfaces statistics ge-1/0/3 detail Physical interface: ge-1/0/3, Enabled, Physical link is Up ... Traffic statistics: Input bytes : 178215885785161 33854736 bps Output bytes : 131059068890210 50354072 bps Input packets: 225075198007 6851 pps Output packets: 140299698663 5525 pps IPv6 transit statistics: Input bytes : 0 Output bytes : 0 Input packets: 0 Output packets: 0 ... I also tried on various L2 & L3 interfaces on my own network (since no L3 on MICE) on various EX platforms, any port speed. It was only on the MX platform where I could get IPv6 traffic stats out on an interface. So, "universal code", but doesn't do the same thing everywhere. Mike already showed the OID doesn't exist, but I tried it as well, and it just doesn't answer with anything under that OID. -- Doug McIntyre <merlyn(a)iphouse.net> ~.~ ipHouse ~.~ Network Engineer/Provisioning/Jack of all Trades

Sept. 25, 2016

Re: IPv6 usage

by Mike Horwath

> On Sep 24, 2016, at 11:43 AM, Frank Bulk <fbulk(a)MYPREMIERONLINE.COM> wrote: > > Perhaps you could walk a few boxes with the OID of 1.3.6.1.2.1.4.30 to see if anything is returned. (http://www.net-snmp.org/docs/mibs/ip.html#ipv6InterfaceTable) I’d be happy to. Doug - do I still have an account on the route servers? Checking my EX4200 stack in my lab: [11:45am] 4 [~]:ori-geeks-org% snmpwalk -v2c -cdon'ttrustyouever switch-stack-of-lab.geeks.org .1.3.6.1.2.1.4.30 IP-MIB::ipv6InterfaceTable = No Such Object available on this agent at this OID with and without preceding dot gives same error. 12.3R6.6 (yes I need to update!) -- Mike Horwath, reachable via drechsau(a)Geeks.ORG

Sept. 24, 2016

Re: IPv6 usage

by Frank Bulk

Perhaps you could walk a few boxes with the OID of 1.3.6.1.2.1.4.30 to see if anything is returned. (http://www.net-snmp.org/docs/mibs/ip.html#ipv6InterfaceTable) Frank -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Mike Horwath Sent: Saturday, September 24, 2016 11:38 AM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] IPv6 usage > On Sep 24, 2016, at 11:37 AM, Frank Bulk <fbulk(a)MYPREMIERONLINE.COM> wrote: > > It appears the JunOS is able to break out the amount of IPv6 (https://www.juniper.net/documentation/en_US/junos16.1/topics/reference/comm…) on an interface. > > Does the EX4200 also support the IP MIB (https://tools.ietf.org/html/rfc4293#section-3.2.3)? If so, it would be great to graph the amount and percentage of IPv6 traffic on most, if not all, interfaces. 4200 recommended is 12.3 not 16.1 so this may be completely moot. -- Mike Horwath, reachable via drechsau(a)Geeks.ORG

Sept. 24, 2016

Re: IPv6 usage

by Mike Horwath

> On Sep 24, 2016, at 11:37 AM, Frank Bulk <fbulk(a)MYPREMIERONLINE.COM> wrote: > > It appears the JunOS is able to break out the amount of IPv6 (https://www.juniper.net/documentation/en_US/junos16.1/topics/reference/comm…) on an interface. > > Does the EX4200 also support the IP MIB (https://tools.ietf.org/html/rfc4293#section-3.2.3)? If so, it would be great to graph the amount and percentage of IPv6 traffic on most, if not all, interfaces. 4200 recommended is 12.3 not 16.1 so this may be completely moot. -- Mike Horwath, reachable via drechsau(a)Geeks.ORG

Sept. 24, 2016

IPv6 usage

by Frank Bulk

It appears the JunOS is able to break out the amount of IPv6 (https://www.juniper.net/documentation/en_US/junos16.1/topics/reference/comm…) on an interface. Does the EX4200 also support the IP MIB (https://tools.ietf.org/html/rfc4293#section-3.2.3)? If so, it would be great to graph the amount and percentage of IPv6 traffic on most, if not all, interfaces. Frank

Sept. 24, 2016

Re: Participant List Updates

by anthonyanderberg＠nu-telecom.net

I've also done a little auditing and found a couple ports that I'd missed in the aggregate graphs. I was expecting the in/out numbers to match more closely so might still be missing some egress bits in the totals... I also saw the earlier thread on Monticello FiberNet, and can confirm that they are documented correctly. Cheers, anthony -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Richard Laager Sent: Thursday, September 22, 2016 8:16 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: [MICE-DISCUSS] Participant List Updates I've updated the website to reflect some participants becoming active: Great Plains Communications Stealth Broadband Yahoo! The following are still pending: ipHouse Remote Switch PCH Sandwich.net Velocity Telephone One port move is still pending: Wikstrom Telephone Company (still active on their current port) I have not historically checked for disconnections. I gave the Cacti graphs a quick read-through, and did some ping & route checks. I wouldn't consider it exhaustive, but I don't see any disconnections. -- Richard

Sept. 23, 2016

Re: PTR's

by Doug McIntyre

On Fri, Sep 23, 2016 at 02:31:40AM +0000, Frank Bulk wrote: > What is MICE's default approach for PTR naming? Is it nothing-unless-asked, AS####.micemn.net or something else? Pretty much done-on-demand. I tried to keep up initially when I got the PTRs, but most didn't care. Just send in requests to hostmaster(a)iphouse.net and we can work them. -- Doug McIntyre <merlyn(a)iphouse.net> ~.~ ipHouse ~.~ Network Engineer/Provisioning/Jack of all Trades

Sept. 23, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by DeLong, Owen

I know it’s more work, but I’d like to suggest testing on 1, then testing on 2. If the results are the same, stick with 2. If necessary for troubleshooting, shut down the second one temporarily and/or migrate back to non-split. I’d hate to see the 1G members dropped from the exchange due to failure of a single line card or switch when that can be avoided. Owen On Sep 21, 2016, at 14:20 , Jeremy Lumby <jlumby(a)MNVOIP.COM<mailto:jlumby@mnvoip.com>> wrote: I am open to input on that. If we run into further errors, it would probably be easier to troubleshoot if it was not split across both, however for load balancing/redundancy it makes sense to split. I do not think there is a ton of load from the 1G members, so I am leaning towards putting them both on 1 From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jason Hanke Sent: Wednesday, September 21, 2016 4:16 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@lists.iphouse.net> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Do you want the LAG split between the 4500 and 4550? Jay On Wed, Sep 21, 2016 at 4:14 PM, Jeremy Lumby <jlumby(a)mnvoip.com<mailto:jlumby@mnvoip.com>> wrote: I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. Thanks, Jeremy -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:07 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com<mailto:hoyosa@gmail.com> > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com<mailto:jlumby@mnvoip.com>> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net<mailto:levipederson@mankatonetworks.net> > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com<mailto:ben.wiechman@arvig.com>> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com<mailto:RGoldberg@compudyne.com>> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM<mailto:jlumby@MNVOIP.COM>> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com<mailto:jlumby@mnvoip.com>> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET>] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET<mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET> > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net<mailto:merlyn@iphouse.net>> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398<tel:%28507%29%20327-2398> mobile > jayhanke(a)neutralpath.net<mailto:jayhanke@neutralpath.net> > www.neutralpath.net<https://urldefense.proofpoint.com/v2/url?u=http-3A__www.neutralpath.net&d=D…> > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net<mailto:jayhanke@neutralpath.net> www.neutralpath.net<https://urldefense.proofpoint.com/v2/url?u=http-3A__www.neutralpath.net&d=D…> ________________________________ To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…> ________________________________ To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1<https://urldefense.proofpoint.com/v2/url?u=http-3A__lists.iphouse.net_cgi-2…>

Sept. 23, 2016

PTR's

by Frank Bulk

What is MICE's default approach for PTR naming? Is it nothing-unless-asked, AS####.micemn.net or something else? Frank

Sept. 23, 2016

Participant List Updates

by Richard Laager

I've updated the website to reflect some participants becoming active: Great Plains Communications Stealth Broadband Yahoo! The following are still pending: ipHouse Remote Switch PCH Sandwich.net Velocity Telephone One port move is still pending: Wikstrom Telephone Company (still active on their current port) I have not historically checked for disconnections. I gave the Cacti graphs a quick read-through, and did some ping & route checks. I wouldn't consider it exhaustive, but I don't see any disconnections. -- Richard

Sept. 23, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Sorry, I mistyped should be 0/2/2 On Thu, Sep 22, 2016 at 1:46 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > Jay, > > I am doing the physical install of the switch now, and I see 0/2/3 is in use. The cross connect/participants list shows Hoyos I see 0/0/1 is available, as well as 0/1/3, and 0/2/2 > > Jeremy. > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jason Hanke > Sent: Wednesday, September 21, 2016 4:25 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Here is the IP: > > MICE Core 1G EX4200-24T > 206.108.255.244/24 > 2001:504:27:0:0:D1AF::244/64 > > I believe this is LAG10 on the core side: > xe-0/2/3 > xe-2/0/16 > > On Wed, Sep 21, 2016 at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: >> Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby >> Sent: Wednesday, September 21, 2016 4:14 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. >> >> Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. >> >> Thanks, >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 4:07 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. >> >> me0.0 is dhcp >> >> root is mice987z >> >> admin is mice987z >> >> ssh is on >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 12:06 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos >> Sent: Wednesday, September 21, 2016 12:05 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. >> >> -- >> Andrew Hoyos >> hoyosa(a)gmail.com >> >> >> >>> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> >>> Probably makes sense to match the current version on the other >>> switches of 12.3R9-S1 >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 11:58 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >>> >>> Anyone have a firmware preference? Or just current juniper recommend? >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 8:38 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >>> >>> Either way, I have available today: >>> >>> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >>> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >>> 1 x 3300 >>> 1 x HP 28284 J >>> 3 x 4200/4500 stacking cables >>> >>> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >>> >>> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >>> >>> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >>> >>> You can also drop me a line at 218-390-5485. >>> >>> Ryan >>> >>> >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Levi Pederson >>> Sent: Wednesday, September 21, 2016 8:28 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> All, >>> >>> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >>> >>> Thank you, >>> >>> >>> Levi Pederson >>> Mankato Networks LLC >>> cell | 612.481.0769 >>> work | 612.787.7392 >>> levipederson(a)mankatonetworks.net >>> >>> >>> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >>> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >>> >>> >>> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >>> provided my work tonight goes as planned I can leave a: >>> >>> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >>> CPU BUILTIN BUILTIN FPC CPU >>> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >>> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >>> >>> >>> in the mice cabinet (or elsewhere). >>> >>> note: no optics... but I could leave a couple DACs probably >>> >>> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >>> >>> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >>> >>> Any preferences whilst I rummage through my oddball grab bag? >>> >>> >>> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >>> Jeremy Lumby <jlumby(a)MNVOIP.COM> >>> Sent: Tuesday, September 20, 2016 3:45 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I am in favor, THANKS GUYS!!! >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Jason Hanke >>> Sent: Tuesday, September 20, 2016 3:41 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >>> >>> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >>> >>> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >>> >>> Jeremy >>> >>> -----Original Message----- >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Doug McIntyre >>> Sent: Tuesday, September 20, 2016 3:15 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >>> > That would make sense, then we are just down to how traffic can >>> > leave the 4200 without going across a vcp >>> >>> Most likely we'd have to kick off (umm. move) the three members that >>> are fiber 1G connections in the expansion slot on the 4200, get a 10G >>> card, optics for both sides, etc. Then decide if we are going to run >>> virtual chassis protocol, or just layer-2 uplink into the two other switches. >>> >>> Or we move the 19 active 1G copper members + 3 1G fiber members off >>> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >>> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >>> >>> > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >>> >>> As I've stated multiple times, I think since VCP is active/passive, >>> there is only one active ring around the the VC through VCP-1 now, and >>> I would expect to see vcp-1 in all paths through the EX4200. >>> >>> We can swap active and passive with the command I posted previously. >>> That way we can troubleshoot if there is a port/cable issue, or if it >>> is an issue with the device itself. >>> >>> Or it could be a defect in this coderev (although I doubt it). >>> >>> >>> -- >>> Doug McIntyre <merlyn(a)iphouse.net> >>> ~.~ ipHouse ~.~ >>> Network Engineer/Provisioning/Jack of all Trades >>> >>> >>> >>> -- >>> Jay Hanke >>> CTO >>> Neutral Path Communications >>> 3 Civic Center Plaza, Suite 204 >>> Mankato, MN 56001 >>> (507) 327-2398 mobile >>> jayhanke(a)neutralpath.net >>> www.neutralpath.net >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >> > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 22, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jeremy Lumby

Jay, I am doing the physical install of the switch now, and I see 0/2/3 is in use. The cross connect/participants list shows Hoyos I see 0/0/1 is available, as well as 0/1/3, and 0/2/2 Jeremy. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jason Hanke Sent: Wednesday, September 21, 2016 4:25 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Here is the IP: MICE Core 1G EX4200-24T 206.108.255.244/24 2001:504:27:0:0:D1AF::244/64 I believe this is LAG10 on the core side: xe-0/2/3 xe-2/0/16 On Wed, Sep 21, 2016 at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: > Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby > Sent: Wednesday, September 21, 2016 4:14 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. > > Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. > > Thanks, > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 4:07 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. > > me0.0 is dhcp > > root is mice987z > > admin is mice987z > > ssh is on > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 12:06 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos > Sent: Wednesday, September 21, 2016 12:05 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. > > -- > Andrew Hoyos > hoyosa(a)gmail.com > > > >> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> >> Probably makes sense to match the current version on the other >> switches of 12.3R9-S1 >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 11:58 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >> >> Anyone have a firmware preference? Or just current juniper recommend? >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 8:38 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >> >> Either way, I have available today: >> >> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >> 1 x 3300 >> 1 x HP 28284 J >> 3 x 4200/4500 stacking cables >> >> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >> >> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >> >> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >> >> You can also drop me a line at 218-390-5485. >> >> Ryan >> >> >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Levi Pederson >> Sent: Wednesday, September 21, 2016 8:28 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> All, >> >> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >> >> Thank you, >> >> >> Levi Pederson >> Mankato Networks LLC >> cell | 612.481.0769 >> work | 612.787.7392 >> levipederson(a)mankatonetworks.net >> >> >> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >> >> >> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >> provided my work tonight goes as planned I can leave a: >> >> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >> CPU BUILTIN BUILTIN FPC CPU >> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >> >> >> in the mice cabinet (or elsewhere). >> >> note: no optics... but I could leave a couple DACs probably >> >> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >> >> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >> >> Any preferences whilst I rummage through my oddball grab bag? >> >> >> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >> Jeremy Lumby <jlumby(a)MNVOIP.COM> >> Sent: Tuesday, September 20, 2016 3:45 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I am in favor, THANKS GUYS!!! >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Jason Hanke >> Sent: Tuesday, September 20, 2016 3:41 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >> >> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >> >> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >> >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Doug McIntyre >> Sent: Tuesday, September 20, 2016 3:15 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >> > That would make sense, then we are just down to how traffic can >> > leave the 4200 without going across a vcp >> >> Most likely we'd have to kick off (umm. move) the three members that >> are fiber 1G connections in the expansion slot on the 4200, get a 10G >> card, optics for both sides, etc. Then decide if we are going to run >> virtual chassis protocol, or just layer-2 uplink into the two other switches. >> >> Or we move the 19 active 1G copper members + 3 1G fiber members off >> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >> >> > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >> >> As I've stated multiple times, I think since VCP is active/passive, >> there is only one active ring around the the VC through VCP-1 now, and >> I would expect to see vcp-1 in all paths through the EX4200. >> >> We can swap active and passive with the command I posted previously. >> That way we can troubleshoot if there is a port/cable issue, or if it >> is an issue with the device itself. >> >> Or it could be a defect in this coderev (although I doubt it). >> >> >> -- >> Doug McIntyre <merlyn(a)iphouse.net> >> ~.~ ipHouse ~.~ >> Network Engineer/Provisioning/Jack of all Trades >> >> >> >> -- >> Jay Hanke >> CTO >> Neutral Path Communications >> 3 Civic Center Plaza, Suite 204 >> Mankato, MN 56001 >> (507) 327-2398 mobile >> jayhanke(a)neutralpath.net >> www.neutralpath.net >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 22, 2016

Re: proxy voting

by Jason Hanke

Proxy voting is no problem. You'll need to designate a proxy in writing in advance with a board member so we know it's legit. An email is sufficient with the ASN and name of the proxy. BTW We're using the Marble Head method of voting again. Jay On Thu, Sep 22, 2016 at 10:13 AM, Andrew Hoyos <hoyosa(a)gmail.com> wrote: > What was the consensus on proxy voting? I seem to recall this was ok. Any special process? > > I was hoping to make the Tuesday meeting in person, but sadly won’t be able to do now. > > -- > Andrew Hoyos > hoyosa(a)gmail.com -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 22, 2016

Re: proxy voting

by Richard Laager

On 09/22/2016 10:13 AM, Andrew Hoyos wrote: > What was the consensus on proxy voting? I seem to recall this was ok. Any special process? This was my take, based on reading the bylaws on the website: On 09/09/2016 01:45 AM, Richard Laager wrote: > If you cannot attend the meeting, I encourage you to designate a proxy, > which must be done in advance. According to the bylaws, you can do this > by email to the Chief Manager. I believe that is Shaun, but if you want > to be safe and nobody confirms who holds that role, send your proxy to > Shaun, Jay, and Reid. Obviously, you should inform the proxy, too. > > If you wish to vote for me, but cannot attend the meeting, you can > designate Mike Johnston as your proxy. I assume Owen will also provide > proxy instructions. -- Richard

Sept. 22, 2016

proxy voting

by Andrew Hoyos

What was the consensus on proxy voting? I seem to recall this was ok. Any special process? I was hoping to make the Tuesday meeting in person, but sadly won’t be able to do now. -- Andrew Hoyos hoyosa(a)gmail.com

Sept. 22, 2016

Re: Update on Website

by Levi Pederson

All, I do believe the cacti was updated at the time of the switch, now several months prior. Just didn't get the website change request in. But we should see what the cacti grapher responds with. Thank you, *Levi Pederson* Mankato Networks LLC cell | 612.481.0769 work | 612.787.7392 levipederson(a)mankatonetworks.net On Thu, Sep 22, 2016 at 10:09 AM, Richard Laager <rlaager(a)wiktel.com> wrote: > On 09/22/2016 10:05 AM, Levi Pederson wrote: > > Monticello FiberNet is now on our remote switch port xe-0/1/2 > > I've updated the website. I suppose Cacti needs an update too, from the > person who handles that. > > -- > Richard >

Sept. 22, 2016

Re: Update on Website

by Levi Pederson

All, Thank you *Levi Pederson* Mankato Networks LLC cell | 612.481.0769 work | 612.787.7392 levipederson(a)mankatonetworks.net On Thu, Sep 22, 2016 at 10:09 AM, Richard Laager <rlaager(a)wiktel.com> wrote: > On 09/22/2016 10:05 AM, Levi Pederson wrote: > > Monticello FiberNet is now on our remote switch port xe-0/1/2 > > I've updated the website. I suppose Cacti needs an update too, from the > person who handles that. > > -- > Richard >

Sept. 22, 2016

Re: Update on Website

by Richard Laager

On 09/22/2016 10:05 AM, Levi Pederson wrote: > Monticello FiberNet is now on our remote switch port xe-0/1/2 I've updated the website. I suppose Cacti needs an update too, from the person who handles that. -- Richard

Sept. 22, 2016

Update on Website

by Levi Pederson

All, We need to make an update on the website. Monticello FiberNet is now on our remote switch port xe-0/1/2 Thank you, *Levi Pederson* Mankato Networks LLC cell | 612.481.0769 work | 612.787.7392 levipederson(a)mankatonetworks.net

Sept. 22, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Richard Laager

On 09/21/2016 04:39 PM, Jason Hanke wrote: > Last I have RIchard requested his port not be set up as a LAG. Yeah, as Doug noted, that changed. I didn't CC you. Sorry about that! -- Richard

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

This is what I have now (updated for Wikstrom Telephone) ae0 NorthernLights GigaPop ae1 Akamai ae2 Netflix ae3 Netflix ae4 Google ae5 CNS Remote Switch ae6 Hurricane Electric ae7 CloudFlare ae8 Airstream (WIN) ae9 Neutral Path Remote Swtich ae10 Wikstrom Telephone ae11 MICE Core 1G Switch On Wed, Sep 21, 2016 at 4:41 PM, Doug McIntyre <merlyn(a)iphouse.net> wrote: > On Wed, Sep 21, 2016 at 04:39:53PM -0500, Jason Hanke wrote: >> Last I have RIchard requested his port not be set up as a LAG. > > He did ask me directly to do so, and I think there was something cc'd > back to MICE-DISCUSS at the time. > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Doug McIntyre

On Wed, Sep 21, 2016 at 04:39:53PM -0500, Jason Hanke wrote: > Last I have RIchard requested his port not be set up as a LAG. He did ask me directly to do so, and I think there was something cc'd back to MICE-DISCUSS at the time. -- Doug McIntyre <merlyn(a)iphouse.net> ~.~ ipHouse ~.~ Network Engineer/Provisioning/Jack of all Trades

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Last I have RIchard requested his port not be set up as a LAG. On Wed, Sep 21, 2016 at 4:34 PM, Justin Krejci <JKrejci(a)usinternet.com> wrote: > According to the MICE participants page, ae10 is for Wikstrom Tel > > ________________________________________ > From: MICE Discuss [MICE-DISCUSS(a)LISTS.IPHOUSE.NET] on behalf of Jason Hanke [jayhanke(a)NEUTRALPATH.NET] > Sent: Wednesday, September 21, 2016 4:31 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Who is 10? > > On Wed, Sep 21, 2016 at 4:30 PM, Doug McIntyre <merlyn(a)iphouse.net> wrote: >> On Wed, Sep 21, 2016 at 04:25:29PM -0500, Jason Hanke wrote: >>> Here is the IP: >>> >>> MICE Core 1G EX4200-24T >>> 206.108.255.244/24 >>> 2001:504:27:0:0:D1AF::244/64 >>> >>> I believe this is LAG10 on the core side: >>> xe-0/2/3 >>> xe-2/0/16 >> >> The next LAG group is ae11. >> >> -- >> Doug McIntyre <merlyn(a)iphouse.net> >> ~.~ ipHouse ~.~ >> Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jeremy Lumby

I think moving the looking glass makes the most sense right now since it is not critical, and then we can move the route servers during an announced maintenance window. When we move forward with the maintenance window, do you think it makes sense to have one route server on the new 4200, and the other on the 4550 using an SPF to copper Ethernet converter? -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jason Hanke Sent: Wednesday, September 21, 2016 4:30 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Let's turn up as a LAG with only one of the two links active. Then activate the second link when we're good and ready. We could also move one of the route servers or maybe the looking glass over to the new switch. On Wed, Sep 21, 2016 at 4:25 PM, Jason Hanke <jayhanke(a)neutralpath.net> wrote: > Here is the IP: > > MICE Core 1G EX4200-24T > 206.108.255.244/24 > 2001:504:27:0:0:D1AF::244/64 > > I believe this is LAG10 on the core side: > xe-0/2/3 > xe-2/0/16 > > On Wed, Sep 21, 2016 at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: >> Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby >> Sent: Wednesday, September 21, 2016 4:14 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. >> >> Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. >> >> Thanks, >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 4:07 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. >> >> me0.0 is dhcp >> >> root is mice987z >> >> admin is mice987z >> >> ssh is on >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 12:06 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos >> Sent: Wednesday, September 21, 2016 12:05 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. >> >> -- >> Andrew Hoyos >> hoyosa(a)gmail.com >> >> >> >>> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> >>> Probably makes sense to match the current version on the other >>> switches of 12.3R9-S1 >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 11:58 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >>> >>> Anyone have a firmware preference? Or just current juniper recommend? >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 8:38 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >>> >>> Either way, I have available today: >>> >>> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >>> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >>> 1 x 3300 >>> 1 x HP 28284 J >>> 3 x 4200/4500 stacking cables >>> >>> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >>> >>> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >>> >>> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >>> >>> You can also drop me a line at 218-390-5485. >>> >>> Ryan >>> >>> >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Levi Pederson >>> Sent: Wednesday, September 21, 2016 8:28 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> All, >>> >>> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >>> >>> Thank you, >>> >>> >>> Levi Pederson >>> Mankato Networks LLC >>> cell | 612.481.0769 >>> work | 612.787.7392 >>> levipederson(a)mankatonetworks.net >>> >>> >>> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >>> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >>> >>> >>> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >>> provided my work tonight goes as planned I can leave a: >>> >>> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >>> CPU BUILTIN BUILTIN FPC CPU >>> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >>> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >>> >>> >>> in the mice cabinet (or elsewhere). >>> >>> note: no optics... but I could leave a couple DACs probably >>> >>> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >>> >>> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >>> >>> Any preferences whilst I rummage through my oddball grab bag? >>> >>> >>> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >>> Jeremy Lumby <jlumby(a)MNVOIP.COM> >>> Sent: Tuesday, September 20, 2016 3:45 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I am in favor, THANKS GUYS!!! >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Jason Hanke >>> Sent: Tuesday, September 20, 2016 3:41 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >>> >>> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >>> >>> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >>> >>> Jeremy >>> >>> -----Original Message----- >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Doug McIntyre >>> Sent: Tuesday, September 20, 2016 3:15 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >>> > That would make sense, then we are just down to how traffic can >>> > leave the 4200 without going across a vcp >>> >>> Most likely we'd have to kick off (umm. move) the three members that >>> are fiber 1G connections in the expansion slot on the 4200, get a 10G >>> card, optics for both sides, etc. Then decide if we are going to run >>> virtual chassis protocol, or just layer-2 uplink into the two other switches. >>> >>> Or we move the 19 active 1G copper members + 3 1G fiber members off >>> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >>> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >>> >>> > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >>> >>> As I've stated multiple times, I think since VCP is active/passive, >>> there is only one active ring around the the VC through VCP-1 now, and >>> I would expect to see vcp-1 in all paths through the EX4200. >>> >>> We can swap active and passive with the command I posted previously. >>> That way we can troubleshoot if there is a port/cable issue, or if it >>> is an issue with the device itself. >>> >>> Or it could be a defect in this coderev (although I doubt it). >>> >>> >>> -- >>> Doug McIntyre <merlyn(a)iphouse.net> >>> ~.~ ipHouse ~.~ >>> Network Engineer/Provisioning/Jack of all Trades >>> >>> >>> >>> -- >>> Jay Hanke >>> CTO >>> Neutral Path Communications >>> 3 Civic Center Plaza, Suite 204 >>> Mankato, MN 56001 >>> (507) 327-2398 mobile >>> jayhanke(a)neutralpath.net >>> www.neutralpath.net >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >> > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Justin Krejci

According to the MICE participants page, ae10 is for Wikstrom Tel ________________________________________ From: MICE Discuss [MICE-DISCUSS(a)LISTS.IPHOUSE.NET] on behalf of Jason Hanke [jayhanke(a)NEUTRALPATH.NET] Sent: Wednesday, September 21, 2016 4:31 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Who is 10? On Wed, Sep 21, 2016 at 4:30 PM, Doug McIntyre <merlyn(a)iphouse.net> wrote: > On Wed, Sep 21, 2016 at 04:25:29PM -0500, Jason Hanke wrote: >> Here is the IP: >> >> MICE Core 1G EX4200-24T >> 206.108.255.244/24 >> 2001:504:27:0:0:D1AF::244/64 >> >> I believe this is LAG10 on the core side: >> xe-0/2/3 >> xe-2/0/16 > > The next LAG group is ae11. > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Who is 10? On Wed, Sep 21, 2016 at 4:30 PM, Doug McIntyre <merlyn(a)iphouse.net> wrote: > On Wed, Sep 21, 2016 at 04:25:29PM -0500, Jason Hanke wrote: >> Here is the IP: >> >> MICE Core 1G EX4200-24T >> 206.108.255.244/24 >> 2001:504:27:0:0:D1AF::244/64 >> >> I believe this is LAG10 on the core side: >> xe-0/2/3 >> xe-2/0/16 > > The next LAG group is ae11. > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Doug McIntyre

On Wed, Sep 21, 2016 at 04:25:29PM -0500, Jason Hanke wrote: > Here is the IP: > > MICE Core 1G EX4200-24T > 206.108.255.244/24 > 2001:504:27:0:0:D1AF::244/64 > > I believe this is LAG10 on the core side: > xe-0/2/3 > xe-2/0/16 The next LAG group is ae11. -- Doug McIntyre <merlyn(a)iphouse.net> ~.~ ipHouse ~.~ Network Engineer/Provisioning/Jack of all Trades

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Let's turn up as a LAG with only one of the two links active. Then activate the second link when we're good and ready. We could also move one of the route servers or maybe the looking glass over to the new switch. On Wed, Sep 21, 2016 at 4:25 PM, Jason Hanke <jayhanke(a)neutralpath.net> wrote: > Here is the IP: > > MICE Core 1G EX4200-24T > 206.108.255.244/24 > 2001:504:27:0:0:D1AF::244/64 > > I believe this is LAG10 on the core side: > xe-0/2/3 > xe-2/0/16 > > On Wed, Sep 21, 2016 at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: >> Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby >> Sent: Wednesday, September 21, 2016 4:14 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. >> >> Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. >> >> Thanks, >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 4:07 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. >> >> me0.0 is dhcp >> >> root is mice987z >> >> admin is mice987z >> >> ssh is on >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 12:06 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos >> Sent: Wednesday, September 21, 2016 12:05 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants >> >> JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. >> >> -- >> Andrew Hoyos >> hoyosa(a)gmail.com >> >> >> >>> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> >>> Probably makes sense to match the current version on the other >>> switches of 12.3R9-S1 >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 11:58 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >>> >>> Anyone have a firmware preference? Or just current juniper recommend? >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Ryan Goldberg >>> Sent: Wednesday, September 21, 2016 8:38 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >>> >>> Either way, I have available today: >>> >>> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >>> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >>> 1 x 3300 >>> 1 x HP 28284 J >>> 3 x 4200/4500 stacking cables >>> >>> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >>> >>> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >>> >>> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >>> >>> You can also drop me a line at 218-390-5485. >>> >>> Ryan >>> >>> >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Levi Pederson >>> Sent: Wednesday, September 21, 2016 8:28 AM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> All, >>> >>> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >>> >>> Thank you, >>> >>> >>> Levi Pederson >>> Mankato Networks LLC >>> cell | 612.481.0769 >>> work | 612.787.7392 >>> levipederson(a)mankatonetworks.net >>> >>> >>> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >>> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >>> >>> >>> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >>> provided my work tonight goes as planned I can leave a: >>> >>> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >>> CPU BUILTIN BUILTIN FPC CPU >>> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >>> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >>> >>> >>> in the mice cabinet (or elsewhere). >>> >>> note: no optics... but I could leave a couple DACs probably >>> >>> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >>> >>> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >>> >>> Any preferences whilst I rummage through my oddball grab bag? >>> >>> >>> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >>> Jeremy Lumby <jlumby(a)MNVOIP.COM> >>> Sent: Tuesday, September 20, 2016 3:45 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> I am in favor, THANKS GUYS!!! >>> >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Jason Hanke >>> Sent: Tuesday, September 20, 2016 3:41 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >>> >>> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >>> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >>> >>> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >>> >>> Jeremy >>> >>> -----Original Message----- >>> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >>> Of Doug McIntyre >>> Sent: Tuesday, September 20, 2016 3:15 PM >>> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >>> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >>> Participants >>> >>> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >>> > That would make sense, then we are just down to how traffic can >>> > leave the 4200 without going across a vcp >>> >>> Most likely we'd have to kick off (umm. move) the three members that >>> are fiber 1G connections in the expansion slot on the 4200, get a 10G >>> card, optics for both sides, etc. Then decide if we are going to run >>> virtual chassis protocol, or just layer-2 uplink into the two other switches. >>> >>> Or we move the 19 active 1G copper members + 3 1G fiber members off >>> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >>> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >>> >>> > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >>> >>> As I've stated multiple times, I think since VCP is active/passive, >>> there is only one active ring around the the VC through VCP-1 now, and >>> I would expect to see vcp-1 in all paths through the EX4200. >>> >>> We can swap active and passive with the command I posted previously. >>> That way we can troubleshoot if there is a port/cable issue, or if it >>> is an issue with the device itself. >>> >>> Or it could be a defect in this coderev (although I doubt it). >>> >>> >>> -- >>> Doug McIntyre <merlyn(a)iphouse.net> >>> ~.~ ipHouse ~.~ >>> Network Engineer/Provisioning/Jack of all Trades >>> >>> >>> >>> -- >>> Jay Hanke >>> CTO >>> Neutral Path Communications >>> 3 Civic Center Plaza, Suite 204 >>> Mankato, MN 56001 >>> (507) 327-2398 mobile >>> jayhanke(a)neutralpath.net >>> www.neutralpath.net >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >>> >>> To unsubscribe from the MICE-DISCUSS list, click the following link: >>> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >>> >> > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Here is the IP: MICE Core 1G EX4200-24T 206.108.255.244/24 2001:504:27:0:0:D1AF::244/64 I believe this is LAG10 on the core side: xe-0/2/3 xe-2/0/16 On Wed, Sep 21, 2016 at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: > Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby > Sent: Wednesday, September 21, 2016 4:14 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. > > Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. > > Thanks, > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 4:07 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. > > me0.0 is dhcp > > root is mice987z > > admin is mice987z > > ssh is on > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 12:06 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos > Sent: Wednesday, September 21, 2016 12:05 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. > > -- > Andrew Hoyos > hoyosa(a)gmail.com > > > >> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> >> Probably makes sense to match the current version on the other >> switches of 12.3R9-S1 >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 11:58 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >> >> Anyone have a firmware preference? Or just current juniper recommend? >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 8:38 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >> >> Either way, I have available today: >> >> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >> 1 x 3300 >> 1 x HP 28284 J >> 3 x 4200/4500 stacking cables >> >> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >> >> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >> >> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >> >> You can also drop me a line at 218-390-5485. >> >> Ryan >> >> >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Levi Pederson >> Sent: Wednesday, September 21, 2016 8:28 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> All, >> >> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >> >> Thank you, >> >> >> Levi Pederson >> Mankato Networks LLC >> cell | 612.481.0769 >> work | 612.787.7392 >> levipederson(a)mankatonetworks.net >> >> >> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >> >> >> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >> provided my work tonight goes as planned I can leave a: >> >> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >> CPU BUILTIN BUILTIN FPC CPU >> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >> >> >> in the mice cabinet (or elsewhere). >> >> note: no optics... but I could leave a couple DACs probably >> >> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >> >> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >> >> Any preferences whilst I rummage through my oddball grab bag? >> >> >> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >> Jeremy Lumby <jlumby(a)MNVOIP.COM> >> Sent: Tuesday, September 20, 2016 3:45 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I am in favor, THANKS GUYS!!! >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Jason Hanke >> Sent: Tuesday, September 20, 2016 3:41 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >> >> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >> >> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >> >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Doug McIntyre >> Sent: Tuesday, September 20, 2016 3:15 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >> > That would make sense, then we are just down to how traffic can >> > leave the 4200 without going across a vcp >> >> Most likely we'd have to kick off (umm. move) the three members that >> are fiber 1G connections in the expansion slot on the 4200, get a 10G >> card, optics for both sides, etc. Then decide if we are going to run >> virtual chassis protocol, or just layer-2 uplink into the two other switches. >> >> Or we move the 19 active 1G copper members + 3 1G fiber members off >> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >> >> > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >> >> As I've stated multiple times, I think since VCP is active/passive, >> there is only one active ring around the the VC through VCP-1 now, and >> I would expect to see vcp-1 in all paths through the EX4200. >> >> We can swap active and passive with the command I posted previously. >> That way we can troubleshoot if there is a port/cable issue, or if it >> is an issue with the device itself. >> >> Or it could be a defect in this coderev (although I doubt it). >> >> >> -- >> Doug McIntyre <merlyn(a)iphouse.net> >> ~.~ ipHouse ~.~ >> Network Engineer/Provisioning/Jack of all Trades >> >> >> >> -- >> Jay Hanke >> CTO >> Neutral Path Communications >> 3 Civic Center Plaza, Suite 204 >> Mankato, MN 56001 >> (507) 327-2398 mobile >> jayhanke(a)neutralpath.net >> www.neutralpath.net >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jeremy Lumby

I will bring some snacks -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:17 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby Sent: Wednesday, September 21, 2016 4:14 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. Thanks, Jeremy -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:07 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Andrew Hoyos

There is a handful of 10g LR SFP+ we donated that should be up there to use in the EX4500/4550 side for this. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 4:16 PM, Ryan Goldberg <RGoldberg(a)compudyne.com> wrote: > > Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby > Sent: Wednesday, September 21, 2016 4:14 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. > > Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. > > Thanks, > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 4:07 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. > > me0.0 is dhcp > > root is mice987z > > admin is mice987z > > ssh is on > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 12:06 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos > Sent: Wednesday, September 21, 2016 12:05 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants > > JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. > > -- > Andrew Hoyos > hoyosa(a)gmail.com > > > >> On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> >> Probably makes sense to match the current version on the other >> switches of 12.3R9-S1 >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 11:58 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. >> >> Anyone have a firmware preference? Or just current juniper recommend? >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Ryan Goldberg >> Sent: Wednesday, September 21, 2016 8:38 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? >> >> Either way, I have available today: >> >> 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS >> 2 x 4200-24 with the 2 x sfp+ module and 2 x PS >> 1 x 3300 >> 1 x HP 28284 J >> 3 x 4200/4500 stacking cables >> >> I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. >> >> I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. >> >> So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. >> >> You can also drop me a line at 218-390-5485. >> >> Ryan >> >> >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Levi Pederson >> Sent: Wednesday, September 21, 2016 8:28 AM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> All, >> >> 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. >> >> Thank you, >> >> >> Levi Pederson >> Mankato Networks LLC >> cell | 612.481.0769 >> work | 612.787.7392 >> levipederson(a)mankatonetworks.net >> >> >> On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: >> We may have a couple EX3300 as well. I can check tomorrow if there is any interest. >> >> >> On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: >> provided my work tonight goes as planned I can leave a: >> >> FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE >> CPU BUILTIN BUILTIN FPC CPU >> PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T >> PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ >> >> >> in the mice cabinet (or elsewhere). >> >> note: no optics... but I could leave a couple DACs probably >> >> I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... >> >> Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. >> >> Any preferences whilst I rummage through my oddball grab bag? >> >> >> From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of >> Jeremy Lumby <jlumby(a)MNVOIP.COM> >> Sent: Tuesday, September 20, 2016 3:45 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> I am in favor, THANKS GUYS!!! >> >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Jason Hanke >> Sent: Tuesday, September 20, 2016 3:41 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. >> >> On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: >> I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. >> >> My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. >> >> Jeremy >> >> -----Original Message----- >> From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf >> Of Doug McIntyre >> Sent: Tuesday, September 20, 2016 3:15 PM >> To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET >> Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G >> Participants >> >> On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: >>> That would make sense, then we are just down to how traffic can >>> leave the 4200 without going across a vcp >> >> Most likely we'd have to kick off (umm. move) the three members that >> are fiber 1G connections in the expansion slot on the 4200, get a 10G >> card, optics for both sides, etc. Then decide if we are going to run >> virtual chassis protocol, or just layer-2 uplink into the two other switches. >> >> Or we move the 19 active 1G copper members + 3 1G fiber members off >> the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. >> Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. >> >>> Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? >> >> As I've stated multiple times, I think since VCP is active/passive, >> there is only one active ring around the the VC through VCP-1 now, and >> I would expect to see vcp-1 in all paths through the EX4200. >> >> We can swap active and passive with the command I posted previously. >> That way we can troubleshoot if there is a port/cable issue, or if it >> is an issue with the device itself. >> >> Or it could be a defect in this coderev (although I doubt it). >> >> >> -- >> Doug McIntyre <merlyn(a)iphouse.net> >> ~.~ ipHouse ~.~ >> Network Engineer/Provisioning/Jack of all Trades >> >> >> >> -- >> Jay Hanke >> CTO >> Neutral Path Communications >> 3 Civic Center Plaza, Suite 204 >> Mankato, MN 56001 >> (507) 327-2398 mobile >> jayhanke(a)neutralpath.net >> www.neutralpath.net >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >> >> To unsubscribe from the MICE-DISCUSS list, click the following link: >> http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >> >

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jeremy Lumby

I am open to input on that. If we run into further errors, it would probably be easier to troubleshoot if it was not split across both, however for load balancing/redundancy it makes sense to split. I do not think there is a ton of load from the 1G members, so I am leaning towards putting them both on 1 From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jason Hanke Sent: Wednesday, September 21, 2016 4:16 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Do you want the LAG split between the 4500 and 4550? Jay On Wed, Sep 21, 2016 at 4:14 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. Thanks, Jeremy -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:07 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net To unsubscribe from the MICE-DISCUSS list, click the following link: http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Ryan Goldberg

Just note: no DACs or optics, so no way to connect at 10gig unless someone brings some snacks -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Jeremy Lumby Sent: Wednesday, September 21, 2016 4:14 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. Thanks, Jeremy -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:07 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jason Hanke

Do you want the LAG split between the 4500 and 4550? Jay On Wed, Sep 21, 2016 at 4:14 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I will probably be there tomorrow to assist in the physical portion of the > installation with Doug/Anthony. I volunteer to be the guinea pig, and test > for loss prior to scheduling a maintenance window to cut over the other 1G > members on. > > Jay, could you give us port assignments for the L2 link to the 4500s, and > an IP for the new switch. > > Thanks, > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of > Ryan Goldberg > Sent: Wednesday, September 21, 2016 4:07 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, it's there. Firmwared (holy crap I forget the hell that is the time > commitment to firmware ex4200) to as listed below and with c13/c14 cables > and stacking cables. > > me0.0 is dhcp > > root is mice987z > > admin is mice987z > > ssh is on > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of > Ryan Goldberg > Sent: Wednesday, September 21, 2016 12:06 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of > Andrew Hoyos > Sent: Wednesday, September 21, 2016 12:05 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > JTAC recommended is R12. Looking at the release notes, seems like a bunch > of minor stuff, but a few PFE crash related fixes that apply to EX4200. > > -- > Andrew Hoyos > hoyosa(a)gmail.com > > > > > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > > > Probably makes sense to match the current version on the other > > switches of 12.3R9-S1 > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > > Of Ryan Goldberg > > Sent: Wednesday, September 21, 2016 11:58 AM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > > > Anyone have a firmware preference? Or just current juniper recommend? > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > > Of Ryan Goldberg > > Sent: Wednesday, September 21, 2016 8:38 AM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > I’m only partially tracking the thread but wasn’t there going to be a > normal 2 x 10gig LAG into the “new” switch? > > > > Either way, I have available today: > > > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > > 1 x 3300 > > 1 x HP 28284 J > > 3 x 4200/4500 stacking cables > > > > I can default and leave one of these in the mice cabinet. No extra > optics or DACs today… I can leave a stacking cable though. > > > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and > would deliver to mice cabinet around 2pm. > > > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know > and I’ll deliver. > > > > You can also drop me a line at 218-390-5485. > > > > Ryan > > > > > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > > Of Levi Pederson > > Sent: Wednesday, September 21, 2016 8:28 AM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > All, > > > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. > Troubleshooting, monitoring and management would be easier with another > 4200/4500/4550. > > > > Thank you, > > > > > > Levi Pederson > > Mankato Networks LLC > > cell | 612.481.0769 > > work | 612.787.7392 > > levipederson(a)mankatonetworks.net > > > > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> > wrote: > > We may have a couple EX3300 as well. I can check tomorrow if there is > any interest. > > > > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> > wrote: > > provided my work tonight goes as planned I can leave a: > > > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 > POE > > CPU BUILTIN BUILTIN FPC CPU > > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 > Base-T > > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > > > > in the mice cabinet (or elsewhere). > > > > note: no optics... but I could leave a couple DACs probably > > > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port > poe switch at 511? So many questions.... > > > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > > > Any preferences whilst I rummage through my oddball grab bag? > > > > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > > Jeremy Lumby <jlumby(a)MNVOIP.COM> > > Sent: Tuesday, September 20, 2016 3:45 PM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > I am in favor, THANKS GUYS!!! > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > > Of Jason Hanke > > Sent: Tuesday, September 20, 2016 3:41 PM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to > MICE to help the cause. > > > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > I am in favor of a regular layer 2 uplink. I think the main reason I > feel this way is it is industry standard, and then the switch has its own > forwarding table. We have seen issues in the past where if the link on a > high volume port goes down, the MAC gets removed from the forwarding table, > and then all of that traffic gets flooded to all other ports until BGP > times out. This seems to be especially problematic when it hits the 1G > ports. > > > > My vision of a future upgrade would be something along the lines of a > 5200, or equiv from another manufacturer that has all of the other switches > uplinked to it. Then we would have separate forwarding tables, a place to > connect remote switches, as well as something that has some 40G, and 100G > capabilities. All of the uplinks would then be easy to monitor/graph > without excessive load on the switch. Copper SFP+/QSFP+ cables can be used > between switches and they are affordable/easy to come by. > > > > Jeremy > > > > -----Original Message----- > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > > Of Doug McIntyre > > Sent: Tuesday, September 20, 2016 3:15 PM > > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > > Participants > > > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > > That would make sense, then we are just down to how traffic can > > > leave the 4200 without going across a vcp > > > > Most likely we'd have to kick off (umm. move) the three members that > > are fiber 1G connections in the expansion slot on the 4200, get a 10G > > card, optics for both sides, etc. Then decide if we are going to run > > virtual chassis protocol, or just layer-2 uplink into the two other > switches. > > > > Or we move the 19 active 1G copper members + 3 1G fiber members off > > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > > > Although- it looks like so far all the paths with loss seem to have > "vcp-1" in them? > > > > As I've stated multiple times, I think since VCP is active/passive, > > there is only one active ring around the the VC through VCP-1 now, and > > I would expect to see vcp-1 in all paths through the EX4200. > > > > We can swap active and passive with the command I posted previously. > > That way we can troubleshoot if there is a port/cable issue, or if it > > is an issue with the device itself. > > > > Or it could be a defect in this coderev (although I doubt it). > > > > > > -- > > Doug McIntyre <merlyn(a)iphouse.net> > > ~.~ ipHouse ~.~ > > Network Engineer/Provisioning/Jack of all Trades > > > > > > > > -- > > Jay Hanke > > CTO > > Neutral Path Communications > > 3 Civic Center Plaza, Suite 204 > > Mankato, MN 56001 > > (507) 327-2398 mobile > > jayhanke(a)neutralpath.net > > www.neutralpath.net > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > -- Jay Hanke CTO Neutral Path Communications 3 Civic Center Plaza, Suite 204 Mankato, MN 56001 (507) 327-2398 mobile jayhanke(a)neutralpath.net www.neutralpath.net

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Jeremy Lumby

I will probably be there tomorrow to assist in the physical portion of the installation with Doug/Anthony. I volunteer to be the guinea pig, and test for loss prior to scheduling a maintenance window to cut over the other 1G members on. Jay, could you give us port assignments for the L2 link to the 4500s, and an IP for the new switch. Thanks, Jeremy -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 4:07 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >

Sept. 21, 2016

Re: EX4200 (1G Switch) Packet Loss -> 10G Participants

by Ryan Goldberg

Ok, it's there. Firmwared (holy crap I forget the hell that is the time commitment to firmware ex4200) to as listed below and with c13/c14 cables and stacking cables. me0.0 is dhcp root is mice987z admin is mice987z ssh is on -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Ryan Goldberg Sent: Wednesday, September 21, 2016 12:06 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants Pulled jinstall-ex-4200-12.3R12.4-domestic-signed just now. -----Original Message----- From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf Of Andrew Hoyos Sent: Wednesday, September 21, 2016 12:05 PM To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G Participants JTAC recommended is R12. Looking at the release notes, seems like a bunch of minor stuff, but a few PFE crash related fixes that apply to EX4200. -- Andrew Hoyos hoyosa(a)gmail.com > On Sep 21, 2016, at 12:01 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > > Probably makes sense to match the current version on the other > switches of 12.3R9-S1 > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 11:58 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Ok, so I’ll leave the 4200-24 with the 2x 10gig and a stacking cable. > > Anyone have a firmware preference? Or just current juniper recommend? > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Ryan Goldberg > Sent: Wednesday, September 21, 2016 8:38 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I’m only partially tracking the thread but wasn’t there going to be a normal 2 x 10gig LAG into the “new” switch? > > Either way, I have available today: > > 1 x 4200-48 poe with the 2 x sfp+ module and 2 x PS > 2 x 4200-24 with the 2 x sfp+ module and 2 x PS > 1 x 3300 > 1 x HP 28284 J > 3 x 4200/4500 stacking cables > > I can default and leave one of these in the mice cabinet. No extra optics or DACs today… I can leave a stacking cable though. > > I’d like to do the defaulting/(and firmwaring) this AM around 10:30 and would deliver to mice cabinet around 2pm. > > So, whoever wants to make the final “I’LL TAKE THAT ONE” call lemme know and I’ll deliver. > > You can also drop me a line at 218-390-5485. > > Ryan > > > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Levi Pederson > Sent: Wednesday, September 21, 2016 8:28 AM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > All, > > 3300's Can't join a Mixed 45**. We'd have to monitor it separately. Troubleshooting, monitoring and management would be easier with another 4200/4500/4550. > > Thank you, > > > Levi Pederson > Mankato Networks LLC > cell | 612.481.0769 > work | 612.787.7392 > levipederson(a)mankatonetworks.net > > > On Tue, Sep 20, 2016 at 10:04 PM, Ben Wiechman <ben.wiechman(a)arvig.com> wrote: > We may have a couple EX3300 as well. I can check tomorrow if there is any interest. > > > On Sep 20, 2016 4:50 PM, "Ryan Goldberg" <RGoldberg(a)compudyne.com> wrote: > provided my work tonight goes as planned I can leave a: > > FPC 2 REV 18 750-021255 BQ0209437984 EX4200-48P, 48 POE > CPU BUILTIN BUILTIN FPC CPU > PIC 0 BUILTIN BUILTIN 48x 10/100/1000 Base-T > PIC 1 REV 04 711-026017 CH0209419573 2x 10GE SFP+ > > > in the mice cabinet (or elsewhere). > > note: no optics... but I could leave a couple DACs probably > > I could leave 24 port non-POE 4200 if preferred. Why do I have 48 port poe switch at 511? So many questions.... > > Or........ I may have a 3300-24 available, which gives 4x SFP+ instead. > > Any preferences whilst I rummage through my oddball grab bag? > > > From: MICE Discuss <MICE-DISCUSS(a)LISTS.IPHOUSE.NET> on behalf of > Jeremy Lumby <jlumby(a)MNVOIP.COM> > Sent: Tuesday, September 20, 2016 3:45 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > I am in favor, THANKS GUYS!!! > > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Jason Hanke > Sent: Tuesday, September 20, 2016 3:41 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > Compudyne has offered to donate an EX4200 with a 2x10G uplink card to MICE to help the cause. > > On Tue, Sep 20, 2016 at 3:31 PM, Jeremy Lumby <jlumby(a)mnvoip.com> wrote: > I am in favor of a regular layer 2 uplink. I think the main reason I feel this way is it is industry standard, and then the switch has its own forwarding table. We have seen issues in the past where if the link on a high volume port goes down, the MAC gets removed from the forwarding table, and then all of that traffic gets flooded to all other ports until BGP times out. This seems to be especially problematic when it hits the 1G ports. > > My vision of a future upgrade would be something along the lines of a 5200, or equiv from another manufacturer that has all of the other switches uplinked to it. Then we would have separate forwarding tables, a place to connect remote switches, as well as something that has some 40G, and 100G capabilities. All of the uplinks would then be easy to monitor/graph without excessive load on the switch. Copper SFP+/QSFP+ cables can be used between switches and they are affordable/easy to come by. > > Jeremy > > -----Original Message----- > From: MICE Discuss [mailto:MICE-DISCUSS@LISTS.IPHOUSE.NET] On Behalf > Of Doug McIntyre > Sent: Tuesday, September 20, 2016 3:15 PM > To: MICE-DISCUSS(a)LISTS.IPHOUSE.NET > Subject: Re: [MICE-DISCUSS] EX4200 (1G Switch) Packet Loss -> 10G > Participants > > On Tue, Sep 20, 2016 at 02:23:00PM -0500, Jeremy Lumby wrote: > > That would make sense, then we are just down to how traffic can > > leave the 4200 without going across a vcp > > Most likely we'd have to kick off (umm. move) the three members that > are fiber 1G connections in the expansion slot on the 4200, get a 10G > card, optics for both sides, etc. Then decide if we are going to run > virtual chassis protocol, or just layer-2 uplink into the two other switches. > > Or we move the 19 active 1G copper members + 3 1G fiber members off > the 4200 altogether and eat up ports on the 4550 with 19 copper SFPs. > Then we wouldn't have to do "Mixed-mode Virtual-Chassis" then either. > > > Although- it looks like so far all the paths with loss seem to have "vcp-1" in them? > > As I've stated multiple times, I think since VCP is active/passive, > there is only one active ring around the the VC through VCP-1 now, and > I would expect to see vcp-1 in all paths through the EX4200. > > We can swap active and passive with the command I posted previously. > That way we can troubleshoot if there is a port/cable issue, or if it > is an issue with the device itself. > > Or it could be a defect in this coderev (although I doubt it). > > > -- > Doug McIntyre <merlyn(a)iphouse.net> > ~.~ ipHouse ~.~ > Network Engineer/Provisioning/Jack of all Trades > > > > -- > Jay Hanke > CTO > Neutral Path Communications > 3 Civic Center Plaza, Suite 204 > Mankato, MN 56001 > (507) 327-2398 mobile > jayhanke(a)neutralpath.net > www.neutralpath.net > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 > > > To unsubscribe from the MICE-DISCUSS list, click the following link: > http://lists.iphouse.net/cgi-bin/wa?SUBED1=MICE-DISCUSS&A=1 >

Sept. 21, 2016

Peering Invitation from Yahoo AS10310 in MICE

by SC Chiu

Hi MICE participants: Yahoo! (AS10310) is now ready to establish peering sessions, please reply us back if you are interested peering in MICE. Our info:Router 1: 206.108.255.59/24, 2001:504:27::2846:0:2/64 Router 2: 206.108.255.58/24, 2001:504:27::2846:0:1/64 Also available in https://www.peeringdb.com/asn/10310 Thanks for peering! Sc Chiu Tech Yahoo, Network Eng, Sr P: 408.3497982 M: 408.9218286 701 First Avenue Sunnyvale CA 94089 cschiu(a)yahoo-inc.com

Sept. 21, 2016